Limits...
Dustiness of fine and nanoscale powders.

Evans DE, Turkevich LA, Roettgers CT, Deye GJ, Baron PA - Ann Occup Hyg (2012)

Bottom Line: For many powders, a significant respirable dustiness was observed.Neither total nor respirable dustiness was found to be correlated with BET surface area, therefore dustiness is not determined by primary particle size.It is therefore unlikely that these materials would exhibit a substantial sub-100 nm particle contribution in a workplace.

View Article: PubMed Central - PubMed

Affiliation: National Institute for Occupational Safety and Health, Chemical Exposure and Monitoring Branch, Division of Applied Research and Technology, 4676 Columbia Parkway, MS-R7, Cincinnati, OH 45226, USA. dje3@cdc.gov

ABSTRACT
Dustiness may be defined as the propensity of a powder to form airborne dust by a prescribed mechanical stimulus; dustiness testing is typically intended to replicate mechanisms of dust generation encountered in workplaces. A novel dustiness testing device, developed for pharmaceutical application, was evaluated in the dustiness investigation of 27 fine and nanoscale powders. The device efficiently dispersed small (mg) quantities of a wide variety of fine and nanoscale powders, into a small sampling chamber. Measurements consisted of gravimetrically determined total and respirable dustiness. The following materials were studied: single and multiwalled carbon nanotubes, carbon nanofibers, and carbon blacks; fumed oxides of titanium, aluminum, silicon, and cerium; metallic nanoparticles (nickel, cobalt, manganese, and silver) silicon carbide, Arizona road dust; nanoclays; and lithium titanate. Both the total and respirable dustiness spanned two orders of magnitude (0.3-37.9% and 0.1-31.8% of the predispersed test powders, respectively). For many powders, a significant respirable dustiness was observed. For most powders studied, the respirable dustiness accounted for approximately one-third of the total dustiness. It is believed that this relationship holds for many fine and nanoscale test powders (i.e. those primarily selected for this study), but may not hold for coarse powders. Neither total nor respirable dustiness was found to be correlated with BET surface area, therefore dustiness is not determined by primary particle size. For a subset of test powders, aerodynamic particle size distributions by number were measured (with an electrical low-pressure impactor and an aerodynamic particle sizer). Particle size modes ranged from approximately 300 nm to several micrometers, but no modes below 100 nm, were observed. It is therefore unlikely that these materials would exhibit a substantial sub-100 nm particle contribution in a workplace.

Show MeSH
. The Venturi dustiness testing device used in this study.
© Copyright Policy - open-access
Related In: Results  -  Collection

License
getmorefigures.php?uid=PMC3750099&req=5

Figure 1: . The Venturi dustiness testing device used in this study.

Mentions: The Venturi dustiness device, utilized in these dustiness measurements, has been described in detail elsewhere (Boundy et al., 2006) but is briefly discussed below. A photograph of the chamber (without the humidity preconditioning antechamber) is presented in Fig. 1.


Dustiness of fine and nanoscale powders.

Evans DE, Turkevich LA, Roettgers CT, Deye GJ, Baron PA - Ann Occup Hyg (2012)

. The Venturi dustiness testing device used in this study.
© Copyright Policy - open-access
Related In: Results  -  Collection

License
Show All Figures
getmorefigures.php?uid=PMC3750099&req=5

Figure 1: . The Venturi dustiness testing device used in this study.
Mentions: The Venturi dustiness device, utilized in these dustiness measurements, has been described in detail elsewhere (Boundy et al., 2006) but is briefly discussed below. A photograph of the chamber (without the humidity preconditioning antechamber) is presented in Fig. 1.

Bottom Line: For many powders, a significant respirable dustiness was observed.Neither total nor respirable dustiness was found to be correlated with BET surface area, therefore dustiness is not determined by primary particle size.It is therefore unlikely that these materials would exhibit a substantial sub-100 nm particle contribution in a workplace.

View Article: PubMed Central - PubMed

Affiliation: National Institute for Occupational Safety and Health, Chemical Exposure and Monitoring Branch, Division of Applied Research and Technology, 4676 Columbia Parkway, MS-R7, Cincinnati, OH 45226, USA. dje3@cdc.gov

ABSTRACT
Dustiness may be defined as the propensity of a powder to form airborne dust by a prescribed mechanical stimulus; dustiness testing is typically intended to replicate mechanisms of dust generation encountered in workplaces. A novel dustiness testing device, developed for pharmaceutical application, was evaluated in the dustiness investigation of 27 fine and nanoscale powders. The device efficiently dispersed small (mg) quantities of a wide variety of fine and nanoscale powders, into a small sampling chamber. Measurements consisted of gravimetrically determined total and respirable dustiness. The following materials were studied: single and multiwalled carbon nanotubes, carbon nanofibers, and carbon blacks; fumed oxides of titanium, aluminum, silicon, and cerium; metallic nanoparticles (nickel, cobalt, manganese, and silver) silicon carbide, Arizona road dust; nanoclays; and lithium titanate. Both the total and respirable dustiness spanned two orders of magnitude (0.3-37.9% and 0.1-31.8% of the predispersed test powders, respectively). For many powders, a significant respirable dustiness was observed. For most powders studied, the respirable dustiness accounted for approximately one-third of the total dustiness. It is believed that this relationship holds for many fine and nanoscale test powders (i.e. those primarily selected for this study), but may not hold for coarse powders. Neither total nor respirable dustiness was found to be correlated with BET surface area, therefore dustiness is not determined by primary particle size. For a subset of test powders, aerodynamic particle size distributions by number were measured (with an electrical low-pressure impactor and an aerodynamic particle sizer). Particle size modes ranged from approximately 300 nm to several micrometers, but no modes below 100 nm, were observed. It is therefore unlikely that these materials would exhibit a substantial sub-100 nm particle contribution in a workplace.

Show MeSH